Epoxy Resin Solid Cast 606 Resin Jewellery 3:1 – 1kg Kit
Epoxy Resin Solid Cast 606 Resin Jewellery 3:1 – 1kg Kit
Couldn't load pickup availability
Kit Includes:
1 x 750g of Part A in a 1 litre Bottle
1 x 250g Part B in a 250ml Bottle
Epoxy Resin Solid Cast 606 Resin Jewellery 3:1 can be cast to create chess pieces or paperweights with embedded items like coins, medals, shells, brand logos, and collectibles.
Long used in industry as a capping resin over metal badges,Epoxy Resin Solid Cast 606 Resin Jewellery 3:1 has ideal surface tension and viscosity.
An superb doming resin for artwork, Solid Cast 606 | Resin Jewellery 3:1 has the ideal surface tension and viscosity.
Solid Solutions for Colour Transparent and Pigments Dyes for a consistent, opaque hue. Pour the finest hard clear resin jewellery on top of wood, artwork, metal badges, or other surfaces.
- Mixing Ratio 3:1 weight
- Working time 40min @ 25° C
- Low Viscosity
- Super Ultra Clear Finish
- Matches 50 coats of varnish
Jewellery Making ✔ Pendants ✔ Bangles ✔ Timber ✔ Earrings ✔ Necklace Making ✔ Clear Doming Resin ✔ Key Rings ✔ Medallions ✔ Food Contact Safe ✔
Temperature Resistance – up to 80 degrees Celsius
DIRECTIONS:
Mix thoroughly in a straight sided, flat bottomed container.
Using a flat ruler shaped mixing stick, mix well, scraping around the sides and base of the container. Mix until the material is crystal clear, free of any streaks.
A thin layer of resin will cure between 20 and 30°C in 24 hours. Do not let the temperature drop below 20°C. Small castings and thin layers of room temperature cured resin can prove brittle in some applications. Maximum impact strength is gained by after 5 days. A maximum block casting of around 250ml can be achieved in a silicone rubber mould.
MIX RATIO:
Measure out 3 parts A to 1 part B by weight using a scale. DO NOT MIX BY VOLUME.
PRODUCT STORAGE:
Always keep caps on bottles when not in use. Store at room temperature (18°) away from direct sunlight.
Do not store on concrete floors.
TIPS FOR USE:
Note resins and hardeners’ have a tendency to go thick and cloudy in cold weather. Check materials are clear and free flowing before using. Material can be reconstitution by standing the bottles with caps removed, in very hot water and stir the contents until the liquids are runny and non-cloudy. Allow to cool back to room temperature before proceeding with mixing.
| Curing temp 20°C |
| Thickness 1mm - 2mm 1 days |
| Maximum impact strenght 5 days |
| Maximum Block Casting 250ml mass |
SAFETY DIRECTIONS:
Work in a well-ventilated area. Avoid contact with eyes and skin. Wear protective gloves and glasses when mixing and using. Over-exposure may cause sensitization. Uncured material can be removed with a solvent or methylated spirit followed by washing with warm soapy water. Always wear a mask when using any solvent cleaner.
Safety precautions to take when working with epoxy resin:
- Keep out of reach of children
- Read Safety Data Sheet before use
- Do not ingest, get on skin, in eyes, or on clothing
- Use only in a well-ventilated area
- Wear protective gloves/protective clothing/eye and face protection
- In case of inadequate ventilation, wear respiratory protection
- If skin irritation or rash occurs, get medical attention
It is crucial that instructions and Safety Data Sheet are read and understood before use.
Download the Safety Data Sheet/Technical Data Sheet Part A Here
Download the Safety Data Sheet/Technical Data Sheet Part B Here
Tracked Shipping Australia Wide
Tracked Shipping Australia Wide
Shipping times vary between 7 to 30 days from time of dispatch. Most of the time your item will arrive within 2 weeks - but I do give an extra 2 week buffer to try and avoid any disappointment.
